diff --git a/Software/src/battery/TESLA-BATTERY.cpp b/Software/src/battery/TESLA-BATTERY.cpp
index e22b8cd8..181bf903 100644
--- a/Software/src/battery/TESLA-BATTERY.cpp
+++ b/Software/src/battery/TESLA-BATTERY.cpp
@@ -8,7 +8,8 @@
 /* Do not change code below unless you are sure what you are doing */
 /* Credits: Most of the code comes from Per Carlen's bms_comms_tesla_model3.py (https://gitlab.com/pelle8/batt2gen24/) */
 
-static unsigned long previousMillis50 = 0;  // will store last time a 50ms CAN Message was send
+static unsigned long previousMillis50 = 0;   // will store last time a 50ms CAN Message was send
+static unsigned long previousMillis100 = 0;  // will store last time a 100ms CAN Message was send
 //0x221 545 VCFRONT_LVPowerState: "GenMsgCycleTime" 50ms
 CAN_frame TESLA_221_1 = {
     .FD = false,
@@ -22,7 +23,12 @@ CAN_frame TESLA_221_2 = {
     .DLC = 8,
     .ID = 0x221,
     .data = {0x61, 0x15, 0x01, 0x00, 0x00, 0x00, 0x20, 0xBA}};  //Contactor Frame 221 - hv_up_for_drive
-
+CAN_frame TESLA_602 = {.FD = false,
+                       .ext_ID = false,
+                       .DLC = 8,
+                       .ID = 0x602,
+                       .data = {0x02, 0x27, 0x05, 0x00, 0x00, 0x00, 0x00, 0x00}};  //Diagnostic request
+static uint8_t stateMachineClearIsolationFault = 0xFF;
 static uint16_t sendContactorClosingMessagesStill = 300;
 static uint16_t battery_cell_max_v = 3300;
 static uint16_t battery_cell_min_v = 3300;
@@ -817,6 +823,10 @@ static const char* hvilStatusState[] = {"NOT OK",
                                         "UNKNOWN(14)",
                                         "UNKNOWN(15)"};
 
+void clearIsolationFault() {
+  //CAN UDS messages to clear a latched isolation fault
+}
+
 void update_values_battery() {  //This function maps all the values fetched via CAN to the correct parameters used for modbus
   //After values are mapped, we perform some safety checks, and do some serial printouts
 
@@ -913,6 +923,12 @@ void update_values_battery() {  //This function maps all the values fetched via
   }
 #endif  // TESLA_MODEL_3Y_BATTERY
 
+  // Check if user requests some action
+  if (datalayer.battery.settings.user_requests_isolation_clear) {
+    stateMachineClearIsolationFault = 0;  //Start the statemachine
+    datalayer.battery.settings.user_requests_isolation_clear = false;
+  }
+
   // Update webserver datalayer
   //0x20A
   datalayer_extended.tesla.status_contactor = battery_contactor;
@@ -2675,7 +2691,7 @@ the first, for a few cycles, then stop all  messages which causes the contactor
   }
 #endif  //defined(TESLA_MODEL_SX_BATTERY) || defined(EXP_TESLA_BMS_DIGITAL_HVIL)
 
-  //Send 30ms message
+  //Send 50ms message
   if (currentMillis - previousMillis50 >= INTERVAL_50_MS) {
     // Check if sending of CAN messages has been delayed too much.
     if ((currentMillis - previousMillis50 >= INTERVAL_50_MS_DELAYED) && (currentMillis > BOOTUP_TIME)) {
@@ -2707,6 +2723,54 @@ the first, for a few cycles, then stop all  messages which causes the contactor
       }
     }
   }
+
+  //Send 100ms message
+  if (currentMillis - previousMillis100 >= INTERVAL_100_MS) {
+    previousMillis100 = currentMillis;
+
+    if (stateMachineClearIsolationFault != 0xFF) {
+      //This implementation should be rewritten to actually replying to the UDS replied sent by the BMS
+      //While this may work, it is not the correct way to implement this clearing logic
+      switch (stateMachineClearIsolationFault) {
+        case 0:
+          TESLA_602.data = {0x02, 0x27, 0x05, 0x00, 0x00, 0x00, 0x00, 0x00};
+          transmit_can_frame(&TESLA_602, can_config.battery);
+          stateMachineClearIsolationFault = 1;
+          break;
+        case 1:
+          TESLA_602.data = {0x30, 0x00, 0x0A, 0x00, 0x00, 0x00, 0x00, 0x00};
+          transmit_can_frame(&TESLA_602, can_config.battery);
+          // BMS should reply 02 50 C0 FF FF FF FF FF
+          stateMachineClearIsolationFault = 2;
+          break;
+        case 2:
+          TESLA_602.data = {0x10, 0x12, 0x27, 0x06, 0x35, 0x34, 0x37, 0x36};
+          transmit_can_frame(&TESLA_602, can_config.battery);
+          // BMS should reply 7E FF FF FF FF FF FF
+          stateMachineClearIsolationFault = 3;
+          break;
+        case 3:
+          TESLA_602.data = {0x21, 0x31, 0x30, 0x33, 0x32, 0x3D, 0x3C, 0x3F};
+          transmit_can_frame(&TESLA_602, can_config.battery);
+          stateMachineClearIsolationFault = 4;
+          break;
+        case 4:
+          TESLA_602.data = {0x22, 0x3E, 0x39, 0x38, 0x3B, 0x3A, 0x00, 0x00};
+          transmit_can_frame(&TESLA_602, can_config.battery);
+          stateMachineClearIsolationFault = 5;
+          break;
+        case 5:
+          TESLA_602.data = {0x04, 0x31, 0x01, 0x04, 0x0A, 0x00, 0x00, 0x00};
+          transmit_can_frame(&TESLA_602, can_config.battery);
+          stateMachineClearIsolationFault = 0xFF;
+          break;
+        default:
+          //Something went wrong. Reset all and cancel
+          stateMachineClearIsolationFault = 0xFF;
+          break;
+      }
+    }
+  }
 }
 
 void print_int_with_units(char* header, int value, char* units) {
diff --git a/Software/src/datalayer/datalayer.h b/Software/src/datalayer/datalayer.h
index d9f943ae..d18bf87f 100644
--- a/Software/src/datalayer/datalayer.h
+++ b/Software/src/datalayer/datalayer.h
@@ -122,8 +122,9 @@ typedef struct {
   uint16_t max_user_set_discharge_voltage_dV = BATTERY_MAX_DISCHARGE_VOLTAGE;
 
   /** Tesla specific settings that are edited on the fly when manually forcing a balance charge for LFP chemistry */
-  /* Bool for specifying if user has requested manual balancing */
+  /* Bool for specifying if user has requested manual function */
   bool user_requests_balancing = false;
+  bool user_requests_isolation_clear = false;
   /* Forced balancing max time & start timestamp */
   uint32_t balancing_time_ms = 3600000;  //1h default, (60min*60sec*1000ms)
   uint32_t balancing_start_time_ms = 0;  //For keeping track when balancing started
diff --git a/Software/src/devboard/webserver/advanced_battery_html.cpp b/Software/src/devboard/webserver/advanced_battery_html.cpp
index b999e6e3..885b8bb2 100644
--- a/Software/src/devboard/webserver/advanced_battery_html.cpp
+++ b/Software/src/devboard/webserver/advanced_battery_html.cpp
@@ -509,6 +509,8 @@ String advanced_battery_processor(const String& var) {
     static const char* falseTrue[] = {"False", "True"};
     static const char* noYes[] = {"No", "Yes"};
     static const char* Fault[] = {"NOT_ACTIVE", "ACTIVE"};
+    //Buttons for user action
+    content += "<button onclick='askClearIsolation()'>Clear isolation fault</button>";
     //0x20A 522 HVP_contatorState
     content += "<h4>Contactor Status: " + String(contactorText[datalayer_extended.tesla.status_contactor]) + "</h4>";
     content += "<h4>HVIL: " + String(hvilStatusState[datalayer_extended.tesla.hvil_status]) + "</h4>";
@@ -1149,6 +1151,19 @@ String advanced_battery_processor(const String& var) {
 
     content += "</div>";
     content += "<script>";
+    content +=
+        "function askClearIsolation() { if (window.confirm('Are you sure you want to clear any active isolation "
+        "fault?')) { "
+        "clearIsolation(); } }";
+    content += "function clearIsolation() {";
+    content += "  var xhr = new XMLHttpRequest();";
+    content += "  xhr.open('GET', '/clearIsolation', true);";
+    content += "  xhr.send();";
+    content += "}";
+    content += "function goToMainPage() { window.location.href = '/'; }";
+    content += "</script>";
+    content += "<script>";
+    content += "<script>";
     content +=
         "function askResetSOH() { if (window.confirm('Are you sure you want to reset degradation data? "
         "Note this should only be used on 2011-2017 24/30kWh batteries!')) { "
diff --git a/Software/src/devboard/webserver/webserver.cpp b/Software/src/devboard/webserver/webserver.cpp
index c4e8c5ce..19e7896d 100644
--- a/Software/src/devboard/webserver/webserver.cpp
+++ b/Software/src/devboard/webserver/webserver.cpp
@@ -385,6 +385,15 @@ void init_webserver() {
     }
   });
 
+  // Route for clearing isolation faults on Tesla
+  server.on("/clearIsolation", HTTP_GET, [](AsyncWebServerRequest* request) {
+    if (WEBSERVER_AUTH_REQUIRED && !request->authenticate(http_username, http_password)) {
+      return request->requestAuthentication();
+    }
+    datalayer.battery.settings.user_requests_isolation_clear = true;
+    request->send(200, "text/plain", "Updated successfully");
+  });
+
   // Route for resetting SOH on Nissan LEAF batteries
   server.on("/resetSOH", HTTP_GET, [](AsyncWebServerRequest* request) {
     if (WEBSERVER_AUTH_REQUIRED && !request->authenticate(http_username, http_password)) {