mirror of
https://github.com/dalathegreat/Battery-Emulator.git
synced 2025-10-03 09:49:32 +02:00
Remove superflous event description
This commit is contained in:
Daniel Öster
parent
89fc610366
commit
733d52d72b
1 changed files with 63 additions and 81 deletions
|
|
@ -73,7 +73,6 @@ static void update_bms_status(void);
|
|||
|
||||
static void log_event(EVENTS_ENUM_TYPE event, uint8_t millisrolloverCount, uint32_t timestamp, uint8_t data);
|
||||
static void print_event_log(void);
|
||||
static void check_ee_write(void);
|
||||
|
||||
uint8_t millisrolloverCount = 0;
|
||||
|
||||
|
|
@ -87,7 +86,6 @@ void run_event_handling(void) {
|
|||
}
|
||||
lastMillis = currentMillis;
|
||||
|
||||
//check_ee_write();
|
||||
update_event_level();
|
||||
}
|
||||
|
||||
|
|
@ -282,88 +280,88 @@ const char* get_event_message_string(EVENTS_ENUM_TYPE event) {
|
|||
case EVENT_CANFD_RX_FAILURE:
|
||||
return "No CANFD communication detected for 60s. Shutting down battery control.";
|
||||
case EVENT_CAN_RX_WARNING:
|
||||
return "ERROR: High amount of corrupted CAN messages detected. Check CAN wire shielding!";
|
||||
return "High amount of corrupted CAN messages detected. Check CAN wire shielding!";
|
||||
case EVENT_CAN_TX_FAILURE:
|
||||
return "ERROR: CAN messages failed to transmit, or no one on the bus to ACK the message!";
|
||||
return "CAN messages failed to transmit, or no one on the bus to ACK the message!";
|
||||
case EVENT_CAN_INVERTER_MISSING:
|
||||
return "Warning: Inverter not sending messages on CAN bus. Check wiring!";
|
||||
return "Inverter not sending messages on CAN bus. Check wiring!";
|
||||
case EVENT_CONTACTOR_WELDED:
|
||||
return "Warning: Contactors sticking/welded. Inspect battery with caution!";
|
||||
return "Contactors sticking/welded. Inspect battery with caution!";
|
||||
case EVENT_CHARGE_LIMIT_EXCEEDED:
|
||||
return "Info: Inverter is charging faster than battery is allowing.";
|
||||
return "Inverter is charging faster than battery is allowing.";
|
||||
case EVENT_DISCHARGE_LIMIT_EXCEEDED:
|
||||
return "Info: Inverter is discharging faster than battery is allowing.";
|
||||
return "Inverter is discharging faster than battery is allowing.";
|
||||
case EVENT_WATER_INGRESS:
|
||||
return "Water leakage inside battery detected. Operation halted. Inspect battery!";
|
||||
case EVENT_12V_LOW:
|
||||
return "12V battery source below required voltage to safely close contactors. Inspect the supply/battery!";
|
||||
case EVENT_SOC_PLAUSIBILITY_ERROR:
|
||||
return "Warning: SOC reported by battery not plausible. Restart battery!";
|
||||
return "SOC reported by battery not plausible. Restart battery!";
|
||||
case EVENT_SOC_UNAVAILABLE:
|
||||
return "Warning: SOC not sent by BMS. Calibrate BMS via app.";
|
||||
return "SOC not sent by BMS. Calibrate BMS via app.";
|
||||
case EVENT_KWH_PLAUSIBILITY_ERROR:
|
||||
return "Info: kWh remaining reported by battery not plausible. Battery needs cycling.";
|
||||
return "kWh remaining reported by battery not plausible. Battery needs cycling.";
|
||||
case EVENT_BALANCING_START:
|
||||
return "Info: Balancing has started";
|
||||
return "Balancing has started";
|
||||
case EVENT_BALANCING_END:
|
||||
return "Info: Balancing has ended";
|
||||
return "Balancing has ended";
|
||||
case EVENT_BATTERY_EMPTY:
|
||||
return "Info: Battery is completely discharged";
|
||||
return "Battery is completely discharged";
|
||||
case EVENT_BATTERY_FULL:
|
||||
return "Info: Battery is fully charged";
|
||||
return "Battery is fully charged";
|
||||
case EVENT_BATTERY_FROZEN:
|
||||
return "Info: Battery is too cold to operate optimally. Consider warming it up!";
|
||||
return "Battery is too cold to operate optimally. Consider warming it up!";
|
||||
case EVENT_BATTERY_CAUTION:
|
||||
return "Info: Battery has raised a general caution flag. Might want to inspect it closely.";
|
||||
return "Battery has raised a general caution flag. Might want to inspect it closely.";
|
||||
case EVENT_BATTERY_CHG_STOP_REQ:
|
||||
return "ERROR: Battery raised caution indicator AND requested charge stop. Inspect battery status!";
|
||||
return "Battery raised caution indicator AND requested charge stop. Inspect battery status!";
|
||||
case EVENT_BATTERY_DISCHG_STOP_REQ:
|
||||
return "ERROR: Battery raised caution indicator AND requested discharge stop. Inspect battery status!";
|
||||
return "Battery raised caution indicator AND requested discharge stop. Inspect battery status!";
|
||||
case EVENT_BATTERY_CHG_DISCHG_STOP_REQ:
|
||||
return "ERROR: Battery raised caution indicator AND requested charge/discharge stop. Inspect battery status!";
|
||||
return "Battery raised caution indicator AND requested charge/discharge stop. Inspect battery status!";
|
||||
case EVENT_BATTERY_REQUESTS_HEAT:
|
||||
return "Info: COLD BATTERY! Battery requesting heating pads to activate!";
|
||||
return "COLD BATTERY! Battery requesting heating pads to activate!";
|
||||
case EVENT_BATTERY_WARMED_UP:
|
||||
return "Info: Battery requesting heating pads to stop. The battery is now warm enough.";
|
||||
return "Battery requesting heating pads to stop. The battery is now warm enough.";
|
||||
case EVENT_BATTERY_OVERHEAT:
|
||||
return "ERROR: Battery overheated. Shutting down to prevent thermal runaway!";
|
||||
return "Battery overheated. Shutting down to prevent thermal runaway!";
|
||||
case EVENT_BATTERY_OVERVOLTAGE:
|
||||
return "Warning: Battery exceeding maximum design voltage. Discharge battery to prevent damage!";
|
||||
return "Battery exceeding maximum design voltage. Discharge battery to prevent damage!";
|
||||
case EVENT_BATTERY_UNDERVOLTAGE:
|
||||
return "Warning: Battery under minimum design voltage. Charge battery to prevent damage!";
|
||||
return "Battery under minimum design voltage. Charge battery to prevent damage!";
|
||||
case EVENT_BATTERY_VALUE_UNAVAILABLE:
|
||||
return "Warning: Battery measurement unavailable. Check 12V power supply and battery wiring!";
|
||||
return "Battery measurement unavailable. Check 12V power supply and battery wiring!";
|
||||
case EVENT_BATTERY_ISOLATION:
|
||||
return "Warning: Battery reports isolation error. High voltage might be leaking to ground. Check battery!";
|
||||
return "Battery reports isolation error. High voltage might be leaking to ground. Check battery!";
|
||||
case EVENT_VOLTAGE_DIFFERENCE:
|
||||
return "Info: Too large voltage diff between the batteries. Second battery cannot join the DC-link";
|
||||
return "Too large voltage diff between the batteries. Second battery cannot join the DC-link";
|
||||
case EVENT_SOH_DIFFERENCE:
|
||||
return "Warning: Large deviation in State of health between packs. Inspect battery.";
|
||||
return "Large deviation in State of health between packs. Inspect battery.";
|
||||
case EVENT_SOH_LOW:
|
||||
return "ERROR: State of health critically low. Battery internal resistance too high to continue. Recycle "
|
||||
return "State of health critically low. Battery internal resistance too high to continue. Recycle "
|
||||
"battery.";
|
||||
case EVENT_HVIL_FAILURE:
|
||||
return "ERROR: Battery interlock loop broken. Check that high voltage / low voltage connectors are seated. "
|
||||
return "Battery interlock loop broken. Check that high voltage / low voltage connectors are seated. "
|
||||
"Battery will be disabled!";
|
||||
case EVENT_PRECHARGE_FAILURE:
|
||||
return "Info: Battery failed to precharge. Check that capacitor is seated on high voltage output.";
|
||||
return "Battery failed to precharge. Check that capacitor is seated on high voltage output.";
|
||||
case EVENT_INTERNAL_OPEN_FAULT:
|
||||
return "ERROR: High voltage cable removed while battery running. Opening contactors!";
|
||||
return "High voltage cable removed while battery running. Opening contactors!";
|
||||
case EVENT_INVERTER_OPEN_CONTACTOR:
|
||||
return "Info: Inverter side opened contactors. Normal operation.";
|
||||
return "Inverter side opened contactors. Normal operation.";
|
||||
case EVENT_INTERFACE_MISSING:
|
||||
return "Info: Configuration trying to use CAN interface not baked into the software. Recompile software!";
|
||||
return "Configuration trying to use CAN interface not baked into the software. Recompile software!";
|
||||
case EVENT_ERROR_OPEN_CONTACTOR:
|
||||
return "Info: Too much time spent in error state. Opening contactors, not safe to continue charging. "
|
||||
return "Too much time spent in error state. Opening contactors, not safe to continue charging. "
|
||||
"Check other error code for reason!";
|
||||
case EVENT_MODBUS_INVERTER_MISSING:
|
||||
return "Info: Modbus inverter has not sent any data. Inspect communication wiring!";
|
||||
return "Modbus inverter has not sent any data. Inspect communication wiring!";
|
||||
case EVENT_CELL_UNDER_VOLTAGE:
|
||||
return "ERROR: CELL UNDERVOLTAGE!!! Stopping battery charging and discharging. Inspect battery!";
|
||||
return "CELL UNDERVOLTAGE!!! Stopping battery charging and discharging. Inspect battery!";
|
||||
case EVENT_CELL_OVER_VOLTAGE:
|
||||
return "ERROR: CELL OVERVOLTAGE!!! Stopping battery charging and discharging. Inspect battery!";
|
||||
return "CELL OVERVOLTAGE!!! Stopping battery charging and discharging. Inspect battery!";
|
||||
case EVENT_CELL_DEVIATION_HIGH:
|
||||
return "ERROR: HIGH CELL DEVIATION!!! Inspect battery!";
|
||||
return "HIGH CELL DEVIATION!!! Inspect battery!";
|
||||
case EVENT_UNKNOWN_EVENT_SET:
|
||||
return "An unknown event was set! Review your code!";
|
||||
case EVENT_DUMMY_INFO:
|
||||
|
|
@ -375,7 +373,7 @@ const char* get_event_message_string(EVENTS_ENUM_TYPE event) {
|
|||
case EVENT_DUMMY_ERROR:
|
||||
return "The dummy error event was set!"; // Don't change this event message!
|
||||
case EVENT_PERSISTENT_SAVE_INFO:
|
||||
return "Info: Failed to save user settings. Namespace full?";
|
||||
return "Failed to save user settings. Namespace full?";
|
||||
case EVENT_SERIAL_RX_WARNING:
|
||||
return "Error in serial function: No data received for some time, see data for minutes";
|
||||
case EVENT_SERIAL_RX_FAILURE:
|
||||
|
|
@ -389,54 +387,54 @@ const char* get_event_message_string(EVENTS_ENUM_TYPE event) {
|
|||
case EVENT_OTA_UPDATE_TIMEOUT:
|
||||
return "OTA update timed out!";
|
||||
case EVENT_EEPROM_WRITE:
|
||||
return "Info: The EEPROM was written";
|
||||
return "The EEPROM was written";
|
||||
case EVENT_RESET_UNKNOWN:
|
||||
return "Info: The board was reset unexpectedly, and reason can't be determined";
|
||||
return "The board was reset unexpectedly, and reason can't be determined";
|
||||
case EVENT_RESET_POWERON:
|
||||
return "Info: The board was reset from a power-on event. Normal operation";
|
||||
return "The board was reset from a power-on event. Normal operation";
|
||||
case EVENT_RESET_EXT:
|
||||
return "Info: The board was reset from an external pin";
|
||||
return "The board was reset from an external pin";
|
||||
case EVENT_RESET_SW:
|
||||
return "Info: The board was reset via software, webserver or OTA. Normal operation";
|
||||
return "The board was reset via software, webserver or OTA. Normal operation";
|
||||
case EVENT_RESET_PANIC:
|
||||
return "Warning: The board was reset due to an exception or panic. Inform developers!";
|
||||
return "The board was reset due to an exception or panic. Inform developers!";
|
||||
case EVENT_RESET_INT_WDT:
|
||||
return "Warning: The board was reset due to an interrupt watchdog timeout. Inform developers!";
|
||||
return "The board was reset due to an interrupt watchdog timeout. Inform developers!";
|
||||
case EVENT_RESET_TASK_WDT:
|
||||
return "Warning: The board was reset due to a task watchdog timeout. Inform developers!";
|
||||
return "The board was reset due to a task watchdog timeout. Inform developers!";
|
||||
case EVENT_RESET_WDT:
|
||||
return "Warning: The board was reset due to other watchdog timeout. Inform developers!";
|
||||
return "The board was reset due to other watchdog timeout. Inform developers!";
|
||||
case EVENT_RESET_DEEPSLEEP:
|
||||
return "Info: The board was reset after exiting deep sleep mode";
|
||||
return "The board was reset after exiting deep sleep mode";
|
||||
case EVENT_RESET_BROWNOUT:
|
||||
return "Info: The board was reset due to a momentary low voltage condition. This is expected during certain "
|
||||
return "The board was reset due to a momentary low voltage condition. This is expected during certain "
|
||||
"operations like flashing via USB";
|
||||
case EVENT_RESET_SDIO:
|
||||
return "Info: The board was reset over SDIO";
|
||||
return "The board was reset over SDIO";
|
||||
case EVENT_RESET_USB:
|
||||
return "Info: The board was reset by the USB peripheral";
|
||||
return "The board was reset by the USB peripheral";
|
||||
case EVENT_RESET_JTAG:
|
||||
return "Info: The board was reset by JTAG";
|
||||
return "The board was reset by JTAG";
|
||||
case EVENT_RESET_EFUSE:
|
||||
return "Info: The board was reset due to an efuse error";
|
||||
return "The board was reset due to an efuse error";
|
||||
case EVENT_RESET_PWR_GLITCH:
|
||||
return "Info: The board was reset due to a detected power glitch";
|
||||
return "The board was reset due to a detected power glitch";
|
||||
case EVENT_RESET_CPU_LOCKUP:
|
||||
return "Warning: The board was reset due to CPU lockup. Inform developers!";
|
||||
return "The board was reset due to CPU lockup. Inform developers!";
|
||||
case EVENT_PAUSE_BEGIN:
|
||||
return "Warning: The emulator is trying to pause the battery.";
|
||||
return "The emulator is trying to pause the battery.";
|
||||
case EVENT_PAUSE_END:
|
||||
return "Info: The emulator is attempting to resume battery operation from pause.";
|
||||
return "The emulator is attempting to resume battery operation from pause.";
|
||||
case EVENT_WIFI_CONNECT:
|
||||
return "Info: Wifi connected.";
|
||||
return "Wifi connected.";
|
||||
case EVENT_WIFI_DISCONNECT:
|
||||
return "Info: Wifi disconnected.";
|
||||
return "Wifi disconnected.";
|
||||
case EVENT_MQTT_CONNECT:
|
||||
return "Info: MQTT connected.";
|
||||
return "MQTT connected.";
|
||||
case EVENT_MQTT_DISCONNECT:
|
||||
return "Info: MQTT disconnected.";
|
||||
return "MQTT disconnected.";
|
||||
case EVENT_EQUIPMENT_STOP:
|
||||
return "ERROR: EQUIPMENT STOP ACTIVATED!!!";
|
||||
return "EQUIPMENT STOP ACTIVATED!!!";
|
||||
default:
|
||||
return "";
|
||||
}
|
||||
|
|
@ -602,19 +600,3 @@ static void print_event_log(void) {
|
|||
}
|
||||
}
|
||||
}
|
||||
|
||||
static void check_ee_write(void) {
|
||||
// Only actually write to flash emulated EEPROM every EE_WRITE_PERIOD_MINUTES minutes,
|
||||
// and only if we've logged any events
|
||||
if (events.ee_timer.elapsed() && (events.nof_logged_events > 0)) {
|
||||
EEPROM.commit();
|
||||
events.nof_eeprom_writes += (events.nof_eeprom_writes < 65535) ? 1 : 0;
|
||||
events.nof_logged_events = 0;
|
||||
|
||||
// We want to know how many writes we have, and to increment the occurrence counter
|
||||
// we need to clear it first. It's just the way life is. Using events is a smooth
|
||||
// way to visualize it in the web UI
|
||||
clear_event(EVENT_EEPROM_WRITE);
|
||||
set_event(EVENT_EEPROM_WRITE, events.nof_eeprom_writes);
|
||||
}
|
||||
}
|
||||
|
|
|
|||
Loading…
Add table
Add a link
Reference in a new issue