diff --git a/Software/USER_SETTINGS.h b/Software/USER_SETTINGS.h
index 1ecc524a..5428d7ad 100644
--- a/Software/USER_SETTINGS.h
+++ b/Software/USER_SETTINGS.h
@@ -12,7 +12,7 @@
 //#define CHADEMO_BATTERY
 //#define IMIEV_CZERO_ION_BATTERY
 //#define KIA_HYUNDAI_64_BATTERY
-#define NISSAN_LEAF_BATTERY
+//#define NISSAN_LEAF_BATTERY
 //#define RENAULT_KANGOO_BATTERY
 //#define RENAULT_ZOE_BATTERY
 //#define SANTA_FE_PHEV_BATTERY
@@ -21,7 +21,7 @@
 
 /* Select inverter communication protocol. See Wiki for which to use with your inverter: https://github.com/dalathegreat/BYD-Battery-Emulator-For-Gen24/wiki */
 //#define BYD_CAN          //Enable this line to emulate a "BYD Battery-Box Premium HVS" over CAN Bus
-#define BYD_MODBUS  //Enable this line to emulate a "BYD 11kWh HVM battery" over Modbus RTU
+//#define BYD_MODBUS  //Enable this line to emulate a "BYD 11kWh HVM battery" over Modbus RTU
 //#define LUNA2000_MODBUS  //Enable this line to emulate a "Luna2000 battery" over Modbus RTU
 //#define PYLON_CAN        //Enable this line to emulate a "Pylontech battery" over CAN bus
 //#define SMA_CAN          //Enable this line to emulate a "BYD Battery-Box H 8.9kWh, 7 mod" over CAN bus
@@ -29,15 +29,15 @@
 //#define SOLAX_CAN        //Enable this line to emulate a "SolaX Triple Power LFP" over CAN bus
 
 /* Other options */
-#define DEBUG_VIA_USB  //Enable this line to have the USB port output serial diagnostic data while program runs
-#define INTERLOCK_REQUIRED  //Nissan LEAF specific setting, if enabled requires both high voltage conenctors to be seated before starting
+//#define DEBUG_VIA_USB  //Enable this line to have the USB port output serial diagnostic data while program runs
+//#define INTERLOCK_REQUIRED  //Nissan LEAF specific setting, if enabled requires both high voltage conenctors to be seated before starting
 //#define CONTACTOR_CONTROL     //Enable this line to have pins 25,32,33 handle automatic precharge/contactor+/contactor- closing sequence
 //#define PWM_CONTACTOR_CONTROL //Enable this line to use PWM logic for contactors, which lower power consumption and heat generation
 //#define DUAL_CAN              //Enable this line to activate an isolated secondary CAN Bus using add-on MCP2515 controller (Needed for FoxESS inverters)
 //#define SERIAL_LINK_RECEIVER  //Enable this line to receive battery data over RS485 pins from another Lilygo (This LilyGo interfaces with inverter)
 //#define SERIAL_LINK_TRANSMITTER  //Enable this line to send battery data over RS485 pins to another Lilygo (This LilyGo interfaces with battery)
-#define WEBSERVER  //Enable this line to enable WiFi, and to run the webserver. See USER_SETTINGS.cpp for the Wifi settings.
-#define MQTT       // Enable this line to enable MQTT
+//#define WEBSERVER  //Enable this line to enable WiFi, and to run the webserver. See USER_SETTINGS.cpp for the Wifi settings.
+//#define MQTT       // Enable this line to enable MQTT
 
 /* Battery limits: These are set in the USER_SETTINGS.cpp file, or later on via the Webserver */
 extern volatile uint16_t BATTERY_WH_MAX;