Add WUP signal GPIO output

Software/Software.ino

@@ -349,6 +349,12 @@ void inform_user_on_battery() {
   // Inform user what battery is used
 #ifdef BMW_I3_BATTERY
   Serial.println("BMW i3 battery selected");
+  pinMode(WUP_PIN, OUTPUT);  //This pin used for WUP relay
+  digitalWrite(WUP_PIN, LOW);
+#ifdef CONTACTOR_CONTROL
+// Contactor control cannot be used when WUP signal is sent on GPIO pins
+#error CONTACTOR CONTROL CANNOT BE USED ON BMW i3
+#endif
 #endif
 #ifdef CHADEMO_BATTERY
   Serial.println("Chademo battery selected");

Software/USER_SETTINGS.h

@@ -8,7 +8,7 @@
 /* To edit battery specific limits, see also the USER_SETTINGS.cpp file*/
 
 /* Select battery used */
-//#define BMW_I3_BATTERY
+#define BMW_I3_BATTERY
 //#define CHADEMO_BATTERY
 //#define IMIEV_CZERO_ION_BATTERY
 //#define KIA_HYUNDAI_64_BATTERY

Software/src/battery/BMW-I3-BATTERY.cpp

@@ -33,10 +33,16 @@ static const int interval5000 = 5000;          // interval (ms) at which send CA
 static const int interval10000 = 10000;        // interval (ms) at which send CAN Messages
 static uint8_t CANstillAlive = 12;             //counter for checking if CAN is still alive
 
+static const uint16_t WUPonDuration = 477;   // in milliseconds how long WUP should be ON after poweron
+static const uint16_t WUPoffDuration = 105;  // in milliseconds how long WUP should be OFF after on pulse
+unsigned long lastChangeTime;                // Variables to store timestamps
+unsigned long turnOnTime;                    // Variables to store timestamps
+enum State { POWERON, STATE_ON, STATE_OFF, STATE_STAY_ON };
+static State WUPState = POWERON;
+
 #define LB_MAX_SOC 1000  //BMS never goes over this value. We use this info to rescale SOC% sent to Inverter
 #define LB_MIN_SOC 0     //BMS never goes below this value. We use this info to rescale SOC% sent to Inverter
 
-
 CAN_frame_t BMW_000 = {.FIR = {.B =
                                    {
                                        .DLC = 4,
@@ -755,11 +761,32 @@ void receive_can_i3_battery(CAN_frame_t rx_frame) {
 }
 void send_can_i3_battery() {
   unsigned long currentMillis = millis();
+
+  //Handle WUP signal
+  if (WUPState == POWERON) {
+    digitalWrite(WUP_PIN, HIGH);
+    turnOnTime = currentMillis;
+    WUPState = STATE_ON;
+  }
+
+  // Check if it's time to change state
+  if (WUPState == STATE_ON && currentMillis - turnOnTime >= WUPonDuration) {
+    WUPState = STATE_OFF;
+    digitalWrite(WUP_PIN, LOW);  // Turn off
+    lastChangeTime = currentMillis;
+  } else if (WUPState == STATE_OFF && currentMillis - lastChangeTime >= WUPoffDuration) {
+    WUPState = STATE_STAY_ON;
+    digitalWrite(WUP_PIN, HIGH);  // Turn on and stay on
+    lastChangeTime = currentMillis;
+  } else if (WUPState == STATE_STAY_ON) {
+    // Do nothing, stay in this state forever
+  }
+
   //Send 10ms message
   if (currentMillis - previousMillis10 >= interval10) {
     previousMillis10 = currentMillis;
 
-    if(!sent_100){
+    if (!sent_100) {
       BMW_000_counter++;
       if (BMW_000_counter > 6) {
         ESP32Can.CANWriteFrame(&BMW_000);

Software/src/devboard/config.h

@@ -26,6 +26,10 @@
 #define PRECHARGE_PIN 25
 #endif
 
+#ifdef BMW_I3_BATTERY
+#define WUP_PIN 25
+#endif
+
 #define SD_MISO_PIN 2
 #define SD_MOSI_PIN 15
 #define SD_SCLK_PIN 14