add extern declaration for bmsReset

Software/USER_SETTINGS.h

@@ -24,7 +24,7 @@
 //#define KIA_HYUNDAI_HYBRID_BATTERY
 //#define MEB_BATTERY
 //#define MG_5_BATTERY
-#define NISSAN_LEAF_BATTERY
+//#define NISSAN_LEAF_BATTERY
 //#define PYLON_BATTERY
 //#define RJXZS_BMS
 //#define RANGE_ROVER_PHEV_BATTERY
@@ -46,7 +46,7 @@
 //#define AFORE_CAN        //Enable this line to emulate an "Afore battery" over CAN bus
 //#define BYD_CAN          //Enable this line to emulate a "BYD Battery-Box Premium HVS" over CAN Bus
 //#define BYD_KOSTAL_RS485 //Enable this line to emulate a "BYD 11kWh HVM battery" over Kostal RS485
-#define BYD_MODBUS  //Enable this line to emulate a "BYD 11kWh HVM battery" over Modbus RTU
+//#define BYD_MODBUS       //Enable this line to emulate a "BYD 11kWh HVM battery" over Modbus RTU
 //#define FOXESS_CAN       //Enable this line to emulate a "HV2600/ECS4100 battery" over CAN bus
 //#define GROWATT_HV_CAN   //Enable this line to emulate a "Growatt High Voltage v1.10 battery" over CAN bus
 //#define GROWATT_LV_CAN   //Enable this line to emulate a "48V Growatt Low Voltage battery" over CAN bus
@@ -63,20 +63,20 @@
 //#define SERIAL_LINK_RECEIVER  //Enable this line to receive battery data over RS485 pins from another Lilygo (This LilyGo interfaces with inverter)
 
 /* Select hardware used for Battery-Emulator */
-#define HW_LILYGO
+//#define HW_LILYGO
 //#define HW_STARK
 //#define HW_3LB
 //#define HW_DEVKIT
 
 /* Contactor settings. If you have a battery that does not activate contactors via CAN, configure this section */
 #define PRECHARGE_TIME_MS 500  //Precharge time in milliseconds. Modify to suit your inverter (See wiki for more info)
-#define CONTACTOR_CONTROL  //Enable this line to have the emulator handle automatic precharge/contactor+/contactor- closing sequence (See wiki for pins)
+//#define CONTACTOR_CONTROL     //Enable this line to have the emulator handle automatic precharge/contactor+/contactor- closing sequence (See wiki for pins)
 //#define CONTACTOR_CONTROL_DOUBLE_BATTERY //Enable this line to have the emulator hardware control secondary set of contactors for double battery setups (See wiki for pins)
-#define PWM_CONTACTOR_CONTROL  //Enable this line to use PWM for CONTACTOR_CONTROL, which lowers power consumption and heat generation. CONTACTOR_CONTROL must be enabled.
+//#define PWM_CONTACTOR_CONTROL //Enable this line to use PWM for CONTACTOR_CONTROL, which lowers power consumption and heat generation. CONTACTOR_CONTROL must be enabled.
 //#define NC_CONTACTORS         //Enable this line to control normally closed contactors. CONTACTOR_CONTROL must be enabled for this option. Extremely rare setting!
-#define PERIODIC_BMS_RESET  //Enable to have the emulator powercycle the connected battery every 24hours via GPIO. Useful for some batteries like Nissan LEAF
+//#define PERIODIC_BMS_RESET    //Enable to have the emulator powercycle the connected battery every 24hours via GPIO. Useful for some batteries like Nissan LEAF
 //#define REMOTE_BMS_RESET      //Enable to allow the emulator to remotely trigger a powercycle of the battery via MQTT. Useful for some batteries like Nissan LEAF
-// PERIODIC_BMS_RESET_AT In 24 Hour format WITHOUT leading 0. e.g 0230 should be 230. Time Zone is set in USER_SETTINGS.cpp
+// PERIODIC_BMS_RESET_AT Uses NTP server, internet required. In 24 Hour format WITHOUT leading 0. e.g 0230 should be 230. Time Zone is set in USER_SETTINGS.cpp
 #define PERIODIC_BMS_RESET_AT 525
 
 /* Shunt/Contactor settings (Optional) */
@@ -111,9 +111,8 @@
 #define WIFI
 //#define WIFICONFIG  //Enable this line to set a static IP address / gateway /subnet mask for the device. see USER_SETTINGS.cpp for the settings
 #define WEBSERVER  //Enable this line to enable WiFi, and to run the webserver. See USER_SETTINGS.cpp for the Wifi settings.
-#define WEBSERVER_AUTH_REQUIRED
-//#define WIFIAP  //When enabled, the emulator will broadcast its own access point Wifi. Can be used at the same time as a normal Wifi connection to a router.
-//#define MDNSRESPONDER  //Enable this line to enable MDNS, allows battery monitor te be found by .local address. Requires WEBSERVER to be enabled.
+#define WIFIAP  //When enabled, the emulator will broadcast its own access point Wifi. Can be used at the same time as a normal Wifi connection to a router.
+#define MDNSRESPONDER  //Enable this line to enable MDNS, allows battery monitor te be found by .local address. Requires WEBSERVER to be enabled.
 #define LOAD_SAVED_SETTINGS_ON_BOOT  // Enable this line to read settings stored via the webserver on boot (overrides Wifi credentials set here)
 //#define FUNCTION_TIME_MEASUREMENT  // Enable this to record execution times and present them in the web UI (WARNING, raises CPU load, do not use for production)
 
@@ -127,7 +126,7 @@
 // may break compatibility with previous versions of MQTT naming. Please refer to USER_SETTINGS.cpp for configuration options.
 
 /* Home Assistant options */
-// #define HA_AUTODISCOVERY  // Enable this line to send Home Assistant autodiscovery messages. If not enabled manual configuration of Home Assitant is required
+#define HA_AUTODISCOVERY  // Enable this line to send Home Assistant autodiscovery messages. If not enabled manual configuration of Home Assitant is required
 
 /* Battery settings */
 // Predefined total energy capacity of the battery in Watt-hours
@@ -142,8 +141,6 @@
 #define BATTERY_MAXTEMPERATURE 500
 // -250 = -25.0 °C , Min temperature (Will produce a battery frozen event if below)
 #define BATTERY_MINTEMPERATURE -250
-// 150 = 15.0 °C , Max difference between min and max temperature (Will produce a battery temperature deviation event if greater)
-#define BATTERY_MAX_TEMPERATURE_DEVIATION 150
 // 300 = 30.0A , Max charge in Amp (Some inverters needs to be limited)
 #define BATTERY_MAX_CHARGE_AMP 300
 // 300 = 30.0A , Max discharge in Amp (Some inverters needs to be limited)
@@ -192,8 +189,4 @@ extern IPAddress subnet;
 #define DEBUG_LOG
 #endif
 
-#if defined(MEB_BATTERY)
-#define PRECHARGE_CONTROL
-#endif
-
 #endif  // __USER_SETTINGS_H__