Remove obsolete compile all hardware workflow

.github/workflows/compile-all-hardware.yml

@@ -1,93 +0,0 @@
-# This is the name of the workflow, visible on GitHub UI.
-name: 🤖 Compile All Hardware
-
-# Here we tell GitHub when to run the workflow.
-on:
-  # The workflow is run when a commit is pushed or for a
-  # Pull Request.
-  - push
-  - pull_request
-
-# This is the list of jobs that will be run concurrently.
-jobs:
-  # This pre-job is run to skip workflows in case a workflow is already run, i.e. because the workflow is triggered by both push and pull_request
-  skip-duplicate-actions:
-    runs-on: ubuntu-latest
-    # Map a step output to a job output
-    outputs:
-      should_skip: ${{ steps.skip_check.outputs.should_skip }}
-    steps:
-      - id: skip_check
-        uses: fkirc/skip-duplicate-actions@v5
-        with:
-          # All of these options are optional, so you can remove them if you are happy with the defaults
-          concurrent_skipping: 'never'
-          skip_after_successful_duplicate: 'true'
-          do_not_skip: '["pull_request", "workflow_dispatch", "schedule"]'
-
-  # Since we use a build matrix, the actual number of jobs
-  # started depends on how many configurations the matrix
-  # will produce.
-
-  # This is the name of the job.
-  build-hardware:
-    needs: skip-duplicate-actions
-    if: needs.skip-duplicate-actions.outputs.should_skip != 'true'
-
-    # Here we tell GitHub that the jobs must be determined
-    # dynamically depending on a matrix configuration.
-    strategy:
-      # The matrix will produce one job for each combination of parameters.
-      matrix:
-        # This is the development board hardware for which the code will be compiled.
-        # FBQN stands for "fully qualified board name", and is used by Arduino to define the hardware to compile for.
-        fqbn:
-          - esp32:esp32:esp32
-          # further ESP32 chips
-          #- esp32:esp32:esp32c3
-          #- esp32:esp32:esp32c2
-          #- esp32:esp32:esp32c6
-          #- esp32:esp32:esp32h2
-          #- esp32:esp32:esp32s3
-        # These are the batteries for which the code will be compiled.
-        battery:
-          - NISSAN_LEAF_BATTERY
-        # These are the emulated inverter communication protocols for which the code will be compiled.
-        inverter:
-          - BYD_CAN
-        # These are the supported hardware platforms for which the code will be compiled.
-        hardware:
-          - HW_LILYGO
-          - HW_STARK
-          - HW_3LB
-          - HW_DEVKIT
-
-    # This is the platform GitHub will use to run our workflow.
-    runs-on: ubuntu-latest
-
-    # This is the list of steps this job will run.
-    steps:
-      # First we clone the repo using the `checkout` action.
-      - name: Checkout
-        uses: actions/checkout@v5
-      
-      # Copy USER_SECRETS.TEMPLATE.h to USER_SECRETS.h
-      - name: Copy USER_SECRETS.TEMPLATE.h to USER_SECRETS.h
-        run: cp ./Software/USER_SECRETS.TEMPLATE.h ./Software/USER_SECRETS.h
-
-      # We use the `arduino/setup-arduino-cli` action to install and
-      # configure the Arduino CLI on the system.
-      - name: Setup Arduino CLI
-        uses: arduino/setup-arduino-cli@v2
-
-      # We then install the platform.
-      - name: Install platform
-        run: |
-          arduino-cli core update-index
-          arduino-cli core install esp32:esp32
-
-      # Finally, we compile the sketch, using the FQBN that was set
-      # in the build matrix, and using build flags to define the
-      # battery and inverter set in the build matrix.
-      - name: Compile Sketch
-        run: arduino-cli compile --fqbn ${{ matrix.fqbn }} --build-property build.partitions=min_spiffs --build-property upload.maximum_size=1966080 --build-property "build.extra_flags=-Wall -Wextra -Wpedantic -Werror -DESP32 -D${{ matrix.battery}} -D${{ matrix.inverter}} -D${{ matrix.hardware}}" ./Software