mirror of
https://github.com/dalathegreat/Battery-Emulator.git
synced 2025-10-03 17:59:27 +02:00
Add Stark board as option
This commit is contained in:
Daniel
parent
44efc43251
commit
d98996b7be
4 changed files with 87 additions and 5 deletions
|
|
@ -342,9 +342,11 @@ void init_stored_settings() {
|
|||
}
|
||||
|
||||
void init_CAN() {
|
||||
// CAN pins
|
||||
// CAN pins
|
||||
#ifdef CAN_SE_PIN
|
||||
pinMode(CAN_SE_PIN, OUTPUT);
|
||||
digitalWrite(CAN_SE_PIN, LOW);
|
||||
#endif
|
||||
CAN_cfg.speed = CAN_SPEED_500KBPS;
|
||||
CAN_cfg.tx_pin_id = GPIO_NUM_27;
|
||||
CAN_cfg.rx_pin_id = GPIO_NUM_26;
|
||||
|
|
@ -419,16 +421,27 @@ void init_contactors() {
|
|||
pinMode(PRECHARGE_PIN, OUTPUT);
|
||||
digitalWrite(PRECHARGE_PIN, LOW);
|
||||
#endif
|
||||
// Init BMS contactor
|
||||
#ifdef HW_STARK // TODO: Rewrite this so LilyGo can aslo handle this BMS contactor
|
||||
pinMode(BMS_POWER, OUTPUT);
|
||||
digitalWrite(BMS_POWER, HIGH);
|
||||
#endif
|
||||
}
|
||||
|
||||
void init_rs485() {
|
||||
// Set up Modbus RTU Server
|
||||
// Set up Modbus RTU Server
|
||||
#ifdef RS485_EN_PIN
|
||||
pinMode(RS485_EN_PIN, OUTPUT);
|
||||
digitalWrite(RS485_EN_PIN, HIGH);
|
||||
#endif
|
||||
#ifdef RS485_SE_PIN
|
||||
pinMode(RS485_SE_PIN, OUTPUT);
|
||||
digitalWrite(RS485_SE_PIN, HIGH);
|
||||
#endif
|
||||
#ifdef PIN_5V_EN
|
||||
pinMode(PIN_5V_EN, OUTPUT);
|
||||
digitalWrite(PIN_5V_EN, HIGH);
|
||||
#endif
|
||||
|
||||
#ifdef MODBUS_INVERTER_SELECTED
|
||||
#ifdef BYD_MODBUS
|
||||
|
|
|
|||
|
|
@ -32,6 +32,10 @@
|
|||
//#define SOFAR_CAN //Enable this line to emulate a "Sofar Energy Storage Inverter High Voltage BMS General Protocol (Extended Frame)" over CAN bus
|
||||
//#define SOLAX_CAN //Enable this line to emulate a "SolaX Triple Power LFP" over CAN bus
|
||||
|
||||
/* Select hardware used for Battery-Emulator */
|
||||
#define HW_LILYGO
|
||||
//#define HW_STARK
|
||||
|
||||
/* Other options */
|
||||
//#define DEBUG_VIA_USB //Enable this line to have the USB port output serial diagnostic data while program runs (WARNING, raises CPU load, do not use for production)
|
||||
//#define DEBUG_CANFD_DATA //Enable this line to have the USB port output CAN-FD data while program runs (WARNING, raises CPU load, do not use for production)
|
||||
|
|
|
|||
|
|
@ -3,11 +3,10 @@
|
|||
|
||||
#include "../../../USER_SETTINGS.h"
|
||||
|
||||
/* Select HW - DONT TOUCH */
|
||||
#define HW_LILYGO
|
||||
|
||||
#if defined(HW_LILYGO)
|
||||
#include "hw_lilygo.h"
|
||||
#elif defined(HW_STARK)
|
||||
#include "hw_stark.h"
|
||||
#elif defined(HW_SJB_V1)
|
||||
#include "hw_sjb_v1.h"
|
||||
#endif
|
||||
|
|
|
|||
66
Software/src/devboard/hal/hw_stark.h
Normal file
66
Software/src/devboard/hal/hw_stark.h
Normal file
|
|
@ -0,0 +1,66 @@
|
|||
#ifndef __HW_STARK06_H__
|
||||
#define __HW_STARK06_H__
|
||||
|
||||
// Board boot-up time
|
||||
#define BOOTUP_TIME 1000 // Time in ms it takes before system is considered fully started up
|
||||
|
||||
// Core assignment
|
||||
#define CORE_FUNCTION_CORE 1
|
||||
#define MODBUS_CORE 0
|
||||
#define WIFI_CORE 0
|
||||
|
||||
// RS485
|
||||
// #define PIN_5V_EN 16 // No function, GPIO 16 used instead as MCP_SCK
|
||||
// #define RS485_EN_PIN 17 // RE, No function, GPIO 17 is instead available as extra GPIO via pin header
|
||||
#define RS485_TX_PIN 22
|
||||
#define RS485_RX_PIN 21
|
||||
// #define RS485_SE_PIN 19 // No function, GPIO 19 is instead available as extra GPIO via pin header
|
||||
|
||||
// CAN settings. CAN_2 is not defined as it can be either MCP2515 or MCP2517, defined by the user settings
|
||||
#define CAN_1_TYPE ESP32CAN
|
||||
|
||||
// CAN1 PIN mappings, do not change these unless you are adding on extra hardware to the PCB
|
||||
#define CAN_TX_PIN GPIO_NUM_27
|
||||
#define CAN_RX_PIN GPIO_NUM_26
|
||||
// #define CAN_SE_PIN 23 // (No function, GPIO 23 used instead as MCP_SCK)
|
||||
|
||||
// CAN2 defines below
|
||||
|
||||
// DUAL_CAN defines
|
||||
//#define MCP2515_SCK 12 // SCK input of MCP2515
|
||||
//#define MCP2515_MOSI 5 // SDI input of MCP2515
|
||||
//#define MCP2515_MISO 34 // SDO output of MCP2515 | Pin 34 is input only, without pullup/down resistors
|
||||
//#define MCP2515_CS 18 // CS input of MCP2515
|
||||
//#define MCP2515_INT 35 // INT output of MCP2515 | | Pin 35 is input only, without pullup/down resistors
|
||||
|
||||
// CAN_FD defines
|
||||
#define MCP2517_SCK 16 // SCK input of MCP2517 (Changed from 12 to 16 since 12 can be used for JTAG TDI)
|
||||
#define MCP2517_SDI 5 // SDI input of MCP2517
|
||||
#define MCP2517_SDO 34 // SDO output of MCP2517
|
||||
#define MCP2517_CS 18 // CS input of MCP2517
|
||||
#define MCP2517_INT 35 // INT output of MCP2517
|
||||
|
||||
// Contactor handling
|
||||
#define POSITIVE_CONTACTOR_PIN 32
|
||||
#define NEGATIVE_CONTACTOR_PIN 33
|
||||
#define PRECHARGE_PIN 25
|
||||
#define BMS_POWER 23 // Also connected to MCP_SCK
|
||||
|
||||
// SD card
|
||||
//#define SD_MISO_PIN 2
|
||||
//#define SD_MOSI_PIN 15
|
||||
//#define SD_SCLK_PIN 14
|
||||
//#define SD_CS_PIN 13
|
||||
|
||||
// LED
|
||||
#define LED_PIN 4
|
||||
#define LED_MAX_BRIGHTNESS 40
|
||||
|
||||
/* ----- Error checks below, don't change (can't be moved to separate file) ----- */
|
||||
#ifndef HW_CONFIGURED
|
||||
#define HW_CONFIGURED
|
||||
#else
|
||||
#error Multiple HW defined! Please select a single HW
|
||||
#endif
|
||||
|
||||
#endif
|
||||
Loading…
Add table
Add a link
Reference in a new issue