mirror of
https://github.com/dalathegreat/Battery-Emulator.git
synced 2025-10-03 09:49:32 +02:00
63371c8b60
* ACAN2517FD lib addition, integrate support for canfd, and add initial EGMP battery capability
101 lines
2.8 KiB
C
101 lines
2.8 KiB
C
#ifndef __CONFIG_H__
|
|
#define __CONFIG_H__
|
|
|
|
// PIN mappings, do not change these unless you are adding on extra hardware to the PCB
|
|
#define PIN_5V_EN 16
|
|
#define CAN_TX_PIN 27
|
|
#define CAN_RX_PIN 26
|
|
#define CAN_SE_PIN 23
|
|
|
|
#define RS485_EN_PIN 17 // 17 /RE
|
|
#define RS485_TX_PIN 22 // 21
|
|
#define RS485_RX_PIN 21 // 22
|
|
#define RS485_SE_PIN 19 // 22 /SHDN
|
|
|
|
#ifdef DUAL_CAN
|
|
#define MCP2515_SCK 12 // SCK input of MCP2515
|
|
#define MCP2515_MOSI 5 // SDI input of MCP2515
|
|
#define MCP2515_MISO 34 // SDO output of MCP2515 | Pin 34 is input only, without pullup/down resistors
|
|
#define MCP2515_CS 18 // CS input of MCP2515
|
|
#define MCP2515_INT 35 // INT output of MCP2515 | | Pin 35 is input only, without pullup/down resistors
|
|
#endif
|
|
|
|
#ifdef CAN_FD
|
|
#define MCP2517_SCK 12 // SCK input of MCP2517
|
|
#define MCP2517_SDI 5 // SDI input of MCP2517
|
|
#define MCP2517_SDO 34 // SDO output of MCP2517
|
|
#define MCP2517_CS 18 // CS input of MCP2517
|
|
#define MCP2517_INT 35 // INT output of MCP2517
|
|
#endif
|
|
|
|
#ifdef CONTACTOR_CONTROL
|
|
#define POSITIVE_CONTACTOR_PIN 32
|
|
#define NEGATIVE_CONTACTOR_PIN 33
|
|
#define PRECHARGE_PIN 25
|
|
#endif
|
|
|
|
#ifdef BMW_I3_BATTERY
|
|
#define WUP_PIN 25
|
|
#endif
|
|
|
|
#define SD_MISO_PIN 2
|
|
#define SD_MOSI_PIN 15
|
|
#define SD_SCLK_PIN 14
|
|
#define SD_CS_PIN 13
|
|
#define WS2812_PIN 4
|
|
|
|
// LED definitions for the board, in order of "priority", DONT CHANGE!
|
|
#define GREEN 0
|
|
#define YELLOW 1
|
|
#define BLUE 2
|
|
#define RED 3
|
|
#define TEST_ALL_COLORS 10
|
|
|
|
// Inverter definitions
|
|
#define STANDBY 0
|
|
#define INACTIVE 1
|
|
#define DARKSTART 2
|
|
#define ACTIVE 3
|
|
#define FAULT 4
|
|
#define UPDATING 5
|
|
#define DISCHARGING 1
|
|
#define CHARGING 2
|
|
|
|
// Common definitions
|
|
#define MAX_AMOUNT_CELLS 192
|
|
#define MAX_CAN_FAILURES 500 // Amount of malformed CAN messages to allow before raising a warning
|
|
|
|
#define INTERVAL_10_MS 10
|
|
#define INTERVAL_20_MS 20
|
|
#define INTERVAL_30_MS 30
|
|
#define INTERVAL_50_MS 50
|
|
#define INTERVAL_100_MS 100
|
|
#define INTERVAL_200_MS 200
|
|
#define INTERVAL_500_MS 500
|
|
#define INTERVAL_640_MS 640
|
|
#define INTERVAL_1_S 1000
|
|
#define INTERVAL_2_S 2000
|
|
#define INTERVAL_5_S 5000
|
|
#define INTERVAL_10_S 10000
|
|
#define INTERVAL_60_S 60000
|
|
|
|
#define INTERVAL_10_MS_DELAYED 15
|
|
#define INTERVAL_20_MS_DELAYED 30
|
|
#define INTERVAL_30_MS_DELAYED 40
|
|
#define INTERVAL_100_MS_DELAYED 120
|
|
#define INTERVAL_500_MS_DELAYED 550
|
|
|
|
#define BOOTUP_TIME 1000 // Time in ms it takes before system is considered fully started up
|
|
|
|
#if defined(DUAL_CAN) && defined(CAN_FD)
|
|
// Check that user did not try to use dual can and fd-can on same hardware pins
|
|
#error CAN-FD AND DUAL-CAN CANNOT BE USED SIMULTANEOUSLY
|
|
#endif
|
|
#if defined(BYD_MODBUS) || defined(LUNA2000_MODBUS)
|
|
#if defined(SERIAL_LINK_RECEIVER) || defined(SERIAL_LINK_TRANSMITTER)
|
|
// Check that Dual LilyGo via RS485 option isn't enabled, this collides with Modbus!
|
|
#error MODBUS CANNOT BE USED IN DOUBLE LILYGO SETUPS! CHECK USER SETTINGS!
|
|
#endif
|
|
#endif
|
|
|
|
#endif
|