mirror of
https://github.com/dalathegreat/Battery-Emulator.git
synced 2025-10-03 09:49:32 +02:00
69 lines
3.6 KiB
C++
69 lines
3.6 KiB
C++
#include "USER_SETTINGS.h"
|
|
#include <string>
|
|
#include "USER_SECRETS.h"
|
|
#include "src/devboard/hal/hal.h"
|
|
|
|
/* This file contains all the battery settings and limits */
|
|
/* They can be defined here, or later on in the WebUI */
|
|
/* Most important is to select which CAN interface each component is connected to */
|
|
/*
|
|
CAN_NATIVE = Native CAN port on the LilyGo & Stark hardware
|
|
CANFD_NATIVE = Native CANFD port on the Stark CMR hardware
|
|
CAN_ADDON_MCP2515 = Add-on CAN MCP2515 connected to GPIO pins
|
|
CANFD_ADDON_MCP2518 = Add-on CAN-FD MCP2518 connected to GPIO pins
|
|
*/
|
|
|
|
volatile CAN_Configuration can_config = {
|
|
.battery = CAN_NATIVE, // Which CAN is your battery connected to?
|
|
.inverter = CAN_NATIVE, // Which CAN is your inverter connected to? (No need to configure incase you use RS485)
|
|
.battery_double = CAN_ADDON_MCP2515, // (OPTIONAL) Which CAN is your second battery connected to?
|
|
.charger = CAN_NATIVE, // (OPTIONAL) Which CAN is your charger connected to?
|
|
.shunt = CAN_NATIVE // (OPTIONAL) Which CAN is your shunt connected to?
|
|
};
|
|
|
|
std::string ssid = WIFI_SSID; // Set in USER_SECRETS.h
|
|
std::string password = WIFI_PASSWORD; // Set in USER_SECRETS.h
|
|
const char* ssidAP = "Battery Emulator"; // Maximum of 63 characters, also used for device name on web interface
|
|
const char* passwordAP = AP_PASSWORD; // Set in USER_SECRETS.h
|
|
const uint8_t wifi_channel = 0; // Set to 0 for automatic channel selection
|
|
|
|
const char* http_username = HTTP_USERNAME; // Set in USER_SECRETS.h
|
|
const char* http_password = HTTP_PASSWORD; // Set in USER_SECRETS.h
|
|
// Set your Static IP address. Only used incase WIFICONFIG is set in USER_SETTINGS.h
|
|
IPAddress local_IP(192, 168, 10, 150);
|
|
IPAddress gateway(192, 168, 10, 1);
|
|
IPAddress subnet(255, 255, 255, 0);
|
|
|
|
// MQTT
|
|
#ifdef COMMON_IMAGE
|
|
std::string mqtt_user;
|
|
std::string mqtt_password;
|
|
#else
|
|
std::string mqtt_user = MQTT_USER; // Set in USER_SECRETS.h
|
|
std::string mqtt_password = MQTT_PASSWORD; // Set in USER_SECRETS.h
|
|
#endif
|
|
|
|
const char* mqtt_topic_name =
|
|
"BE"; // Custom MQTT topic name. Previously, the name was automatically set to "battery-emulator_esp32-XXXXXX"
|
|
const char* mqtt_object_id_prefix =
|
|
"be_"; // Custom prefix for MQTT object ID. Previously, the prefix was automatically set to "esp32-XXXXXX_"
|
|
const char* mqtt_device_name =
|
|
"Battery Emulator"; // Custom device name in Home Assistant. Previously, the name was automatically set to "BatteryEmulator_esp32-XXXXXX"
|
|
const char* ha_device_id =
|
|
"battery-emulator"; // Custom device ID in Home Assistant. Previously, the ID was always "battery-emulator"
|
|
|
|
/* Charger settings (Optional, when using generator charging) */
|
|
volatile float CHARGER_SET_HV = 384; // Reasonably appropriate 4.0v per cell charging of a 96s pack
|
|
volatile float CHARGER_MAX_HV = 420; // Max permissible output (VDC) of charger
|
|
volatile float CHARGER_MIN_HV = 200; // Min permissible output (VDC) of charger
|
|
volatile float CHARGER_MAX_POWER = 3300; // Max power capable of charger, as a ceiling for validating config
|
|
volatile float CHARGER_MAX_A = 11.5; // Max current output (amps) of charger
|
|
volatile float CHARGER_END_A = 1.0; // Current at which charging is considered complete
|
|
|
|
#ifdef PERIODIC_BMS_RESET_AT
|
|
// A list of rules for your zone can be obtained from https://github.com/esp8266/Arduino/blob/master/cores/esp8266/TZ.h
|
|
const char* time_zone =
|
|
"GMT0BST,M3.5.0/1,M10.5.0"; // TimeZone rule for Europe/London including daylight adjustment rules (optional)
|
|
const char* ntpServer1 = "pool.ntp.org";
|
|
const char* ntpServer2 = "time.nist.gov";
|
|
#endif
|