mirror of
https://github.com/dalathegreat/Battery-Emulator.git
synced 2025-10-03 01:39:30 +02:00
70 lines
2.7 KiB
C
70 lines
2.7 KiB
C
#ifndef __USER_SETTINGS_H__
|
|
#define __USER_SETTINGS_H__
|
|
#include <WiFi.h>
|
|
#include <stdint.h>
|
|
#include "src/devboard/utils/types.h"
|
|
|
|
/* This file is being transitioned towards COMMON_IMAGE. Use v8.16 if you are taking this software into use! */
|
|
|
|
/* Select hardware used for Battery-Emulator */
|
|
//#define HW_LILYGO
|
|
//#define HW_STARK
|
|
//#define HW_3LB
|
|
//#define HW_DEVKIT
|
|
|
|
/* Shunt/Contactor settings (Optional) */
|
|
//#define BMW_SBOX // SBOX relay control & battery current/voltage measurement
|
|
|
|
/* Automatic Precharge settings (Optional) If you have a battery that expects an external voltage applied before opening contactors (within the battery), configure this section */
|
|
//#define PRECHARGE_CONTROL //Enable this line to control a modified HIA4V1 via PWM on the HIA4V1_PIN (see Wiki and HAL for pin definition)
|
|
//#define INVERTER_DISCONNECT_CONTACTOR_IS_NORMALLY_OPEN //Enable this line if you use a normally open contactor instead of normally closed
|
|
|
|
/* Connectivity options */
|
|
//#define WIFICONFIG //Enable this line to set a static IP address / gateway /subnet mask for the device. see USER_SETTINGS.cpp for the settings
|
|
|
|
#define MQTT_QOS 0 // MQTT Quality of Service (0, 1, or 2)
|
|
#define MQTT_PUBLISH_CELL_VOLTAGES // Enable this line to publish cell voltages to MQTT
|
|
#define MQTT_TIMEOUT 2000 // MQTT timeout in milliseconds
|
|
|
|
/* Do not change any code below this line */
|
|
/* Only change battery specific settings above and in "USER_SETTINGS.cpp" */
|
|
typedef struct {
|
|
CAN_Interface battery;
|
|
CAN_Interface inverter;
|
|
CAN_Interface battery_double;
|
|
CAN_Interface charger;
|
|
CAN_Interface shunt;
|
|
} CAN_Configuration;
|
|
extern volatile CAN_Configuration can_config;
|
|
extern volatile uint8_t AccessPointEnabled;
|
|
extern const uint8_t wifi_channel;
|
|
extern volatile float CHARGER_SET_HV;
|
|
extern volatile float CHARGER_MAX_HV;
|
|
extern volatile float CHARGER_MIN_HV;
|
|
extern volatile float CHARGER_MAX_POWER;
|
|
extern volatile float CHARGER_MAX_A;
|
|
extern volatile float CHARGER_END_A;
|
|
|
|
#include "src/communication/equipmentstopbutton/comm_equipmentstopbutton.h"
|
|
|
|
// Equipment stop button behavior. Use NC button for safety reasons.
|
|
//LATCHING_SWITCH - Normally closed (NC), latching switch. When pressed it activates e-stop
|
|
//MOMENTARY_SWITCH - Short press to activate e-stop, long 15s press to deactivate. E-stop is persistent between reboots
|
|
|
|
#ifdef EQUIPMENT_STOP_BUTTON
|
|
const STOP_BUTTON_BEHAVIOR stop_button_default_behavior = STOP_BUTTON_BEHAVIOR::MOMENTARY_SWITCH;
|
|
#else
|
|
const STOP_BUTTON_BEHAVIOR stop_button_default_behavior = STOP_BUTTON_BEHAVIOR::NOT_CONNECTED;
|
|
#endif
|
|
|
|
#ifdef WIFICONFIG
|
|
extern IPAddress local_IP;
|
|
extern IPAddress gateway;
|
|
extern IPAddress subnet;
|
|
#endif
|
|
|
|
#if defined(MEB_BATTERY)
|
|
#define PRECHARGE_CONTROL
|
|
#endif
|
|
|
|
#endif // __USER_SETTINGS_H__
|