mirror of
https://github.com/dalathegreat/Battery-Emulator.git
synced 2025-10-03 17:59:27 +02:00
118 lines
7.1 KiB
C
118 lines
7.1 KiB
C
#ifndef __USER_SETTINGS_H__
|
|
#define __USER_SETTINGS_H__
|
|
#include <stdint.h>
|
|
|
|
/* This file contains all the battery/inverter protocol settings Battery-Emulator software */
|
|
/* To switch between batteries/inverters, uncomment a line to enable, comment out to disable. */
|
|
/* There are also some options for battery limits and extra functionality */
|
|
/* To edit battery specific limits, see also the USER_SETTINGS.cpp file*/
|
|
|
|
/* Select battery used */
|
|
//#define BMW_I3_BATTERY
|
|
//#define BYD_ATTO_3_BATTERY
|
|
//#define CHADEMO_BATTERY //NOTE: inherently enables CONTACTOR_CONTROL below
|
|
//#define IMIEV_CZERO_ION_BATTERY
|
|
//#define JAGUAR_IPACE_BATTERY
|
|
//#define KIA_HYUNDAI_64_BATTERY
|
|
//#define KIA_E_GMP_BATTERY
|
|
//#define KIA_HYUNDAI_HYBRID_BATTERY
|
|
//#define MG_5_BATTERY
|
|
//#define NISSAN_LEAF_BATTERY
|
|
//#define PYLON_BATTERY
|
|
//#define RJXZS_BMS
|
|
//#define RENAULT_KANGOO_BATTERY
|
|
//#define RENAULT_ZOE_GEN1_BATTERY
|
|
//#define RENAULT_ZOE_GEN2_BATTERY
|
|
//#define SANTA_FE_PHEV_BATTERY
|
|
//#define TESLA_MODEL_3_BATTERY
|
|
//#define VOLVO_SPA_BATTERY
|
|
//#define TEST_FAKE_BATTERY
|
|
//#define DOUBLE_BATTERY //Enable this line if you use two identical batteries at the same time (requires DUAL_CAN setup)
|
|
|
|
/* Select inverter communication protocol. See Wiki for which to use with your inverter: https://github.com/dalathegreat/BYD-Battery-Emulator-For-Gen24/wiki */
|
|
//#define BYD_CAN //Enable this line to emulate a "BYD Battery-Box Premium HVS" over CAN Bus
|
|
//#define BYD_SMA //Enable this line to emulate a SMA compatible "BYD Battery-Box HVS 10.2KW battery" over CAN bus
|
|
//#define BYD_MODBUS //Enable this line to emulate a "BYD 11kWh HVM battery" over Modbus RTU
|
|
//#define PYLON_CAN //Enable this line to emulate a "Pylontech battery" over CAN bus
|
|
//#define SMA_CAN //Enable this line to emulate a "BYD Battery-Box H 8.9kWh, 7 mod" over CAN bus
|
|
//#define SMA_TRIPOWER_CAN //Enable this line to emulate a "SMA Home Storage battery" over CAN bus
|
|
//#define SOFAR_CAN //Enable this line to emulate a "Sofar Energy Storage Inverter High Voltage BMS General Protocol (Extended Frame)" over CAN bus
|
|
//#define SOLAX_CAN //Enable this line to emulate a "SolaX Triple Power LFP" over CAN bus
|
|
|
|
/* Select hardware used for Battery-Emulator */
|
|
#define HW_LILYGO
|
|
//#define HW_STARK
|
|
|
|
/* Other options */
|
|
//#define DEBUG_VIA_USB //Enable this line to have the USB port output serial diagnostic data while program runs (WARNING, raises CPU load, do not use for production)
|
|
//#define DEBUG_CANFD_DATA //Enable this line to have the USB port output CAN-FD data while program runs (WARNING, raises CPU load, do not use for production)
|
|
//#define INTERLOCK_REQUIRED //Nissan LEAF specific setting, if enabled requires both high voltage conenctors to be seated before starting
|
|
//#define CONTACTOR_CONTROL //Enable this line to have pins 25,32,33 handle automatic precharge/contactor+/contactor- closing sequence
|
|
//#define PWM_CONTACTOR_CONTROL //Enable this line to use PWM logic for contactors, which lower power consumption and heat generation
|
|
//#define DUAL_CAN //Enable this line to activate an isolated secondary CAN Bus using add-on MCP2515 chip (Needed for some inverters / double battery)
|
|
//#define CAN_FD //Enable this line to activate an isolated secondary CAN-FD bus using add-on MCP2518FD chip / Native CANFD on Stark board
|
|
//#define USE_CANFD_INTERFACE_AS_CLASSIC_CAN // Enable this line if you intend to use the CANFD as normal CAN
|
|
//#define SERIAL_LINK_RECEIVER //Enable this line to receive battery data over RS485 pins from another Lilygo (This LilyGo interfaces with inverter)
|
|
//#define SERIAL_LINK_TRANSMITTER //Enable this line to send battery data over RS485 pins to another Lilygo (This LilyGo interfaces with battery)
|
|
#define WEBSERVER //Enable this line to enable WiFi, and to run the webserver. See USER_SETTINGS.cpp for the Wifi settings.
|
|
#define WEBSERVER_AUTH_REQUIRED \
|
|
false //Enable this line to enable webserver authentication. See USER_SETTINGS.cpp setting the credentials.
|
|
#define WIFIAP //Disable this line to permanently disable WIFI AP mode (make sure to hardcode ssid and password of you home wifi network). When enabled WIFI AP can still be disabled by a setting in the future.
|
|
#define MDNSRESPONDER //Enable this line to enable MDNS, allows battery monitor te be found by .local address. Requires WEBSERVER to be enabled.
|
|
#define LOAD_SAVED_SETTINGS_ON_BOOT //Enable this line to read settings stored via the webserver on boot (overrides Wifi/battery settings set below)
|
|
//#define FUNCTION_TIME_MEASUREMENT // Enable this to record execution times and present them in the web UI (WARNING, raises CPU load, do not use for production)
|
|
|
|
/* MQTT options */
|
|
// #define MQTT // Enable this line to enable MQTT
|
|
#define MQTT_SERVER "192.168.xxx.yyy"
|
|
#define MQTT_PORT 1883
|
|
|
|
/* Home Assistant options */
|
|
#define HA_AUTODISCOVERY // Enable this line to send Home Assistant autodiscovery messages. If not enabled manual configuration of Home Assitant is required
|
|
|
|
/* Event options*/
|
|
#define DUMMY_EVENT_ENABLED false //Enable this line to have a dummy event that gets logged to test the interface
|
|
|
|
/* Select charger used (Optional) */
|
|
//#define CHEVYVOLT_CHARGER //Enable this line to control a Chevrolet Volt charger connected to battery - for example, when generator charging or using an inverter without a charging function.
|
|
//#define NISSANLEAF_CHARGER //Enable this line to control a Nissan LEAF PDM connected to battery - for example, when generator charging
|
|
|
|
/* Battery settings */
|
|
// Predefined total energy capacity of the battery in Watt-hours
|
|
#define BATTERY_WH_MAX 30000
|
|
// Increases battery life. If true will rescale SOC between the configured min/max-percentage
|
|
#define BATTERY_USE_SCALED_SOC true
|
|
// 8000 = 80.0% , Max percentage the battery will charge to (Inverter gets 100% when reached)
|
|
#define BATTERY_MAXPERCENTAGE 8000
|
|
// 2000 = 20.0% , Min percentage the battery will discharge to (Inverter gets 0% when reached)
|
|
#define BATTERY_MINPERCENTAGE 2000
|
|
// 300 = 30.0A , BYD CAN specific setting, Max charge in Amp (Some inverters needs to be limited)
|
|
#define BATTERY_MAX_CHARGE_AMP 300
|
|
// 300 = 30.0A , BYD CAN specific setting, Max discharge in Amp (Some inverters needs to be limited)
|
|
#define BATTERY_MAX_DISCHARGE_AMP 300
|
|
|
|
/* Do not change any code below this line unless you are sure what you are doing */
|
|
/* Only change battery specific settings in "USER_SETTINGS.h" */
|
|
typedef enum { CAN_NATIVE = 0, CANFD_NATIVE = 1, CAN_ADDON_MCP2515 = 2, CAN_ADDON_FD_MCP2518 = 3 } CAN_Interface;
|
|
typedef struct {
|
|
CAN_Interface battery;
|
|
CAN_Interface inverter;
|
|
CAN_Interface battery_double;
|
|
CAN_Interface charger;
|
|
} CAN_Configuration;
|
|
extern volatile CAN_Configuration can_config;
|
|
extern volatile uint8_t AccessPointEnabled;
|
|
extern const uint8_t wifi_channel;
|
|
extern volatile float charger_setpoint_HV_VDC;
|
|
extern volatile float charger_setpoint_HV_IDC;
|
|
extern volatile float charger_setpoint_HV_IDC_END;
|
|
extern volatile float CHARGER_SET_HV;
|
|
extern volatile float CHARGER_MAX_HV;
|
|
extern volatile float CHARGER_MIN_HV;
|
|
extern volatile float CHARGER_MAX_POWER;
|
|
extern volatile float CHARGER_MAX_A;
|
|
extern volatile float CHARGER_END_A;
|
|
extern bool charger_HV_enabled;
|
|
extern bool charger_aux12V_enabled;
|
|
|
|
#endif // __USER_SETTINGS_H__
|